Expert Answers about Thor Four Winds Motorhome

• Will Air Bags for a 2018 Thor 24HE Lift the Rear Providing More Ground Clearance
• The correct air bag kit for a 2018 Thor 24HE on a Ford E-350 Cutaway Chassis is the Firestone Ride-Rite Air Helper Spring Kit part # F2061. This system is designed to provide rear end support to reduce sag. It is not designed to lift the rear but in many cases we do see this happens with enough pressure. That said, whether or not it will provide enough lift to prevent bottoming out on any one particular driveway is anyone's guess as the amount of lift and slope of driveway are variables...
  view full answer...


• Why Does The Valterra HydroFlush Need To Be Installed On The Top Of The Black Tank
• The Valterra HydroFlush RV Black Tank Flush System # VAL42RB is recommended to be installed on the top of the tank so it's out of the way of everything and isn't a point that solids could get caught on or in the event that the backflow valve failed it'd be less likely to drain the tank. If you don't have access above the tank and don't want to install an access panel in the floor of the motorhome then you can try installing it higher up on the side of the tank to hopefully prevent either...
  view full answer...


• Brake Controller Plug Location for 2019 Thor Four Winds 24E Motorhome
• Your 2019 Thor Four Winds 24E Motorhome is built on a Ford E-450 chassis so the plug you're going to need will be located behind the storage (coin) compartment above the radio (see attached). If you don't already have a brake controller I highly recommend the Prodigy P3 # 90195 which will connect to that plug using the Adapter # 3034-P. I really like the P3 because it has an LCD screen that communicates directly what is going on with minimal codes. Attached are some photos for you to...
  view full answer...


• Rear Anti-Sway Bar Installation For A 2014 Thor Four Winds Motorhome
• When installing the Roadmaster Rear Anti-Sway Bar Item # RM-1139-147 you can reuse the bolt holes in your frame for your links as long as they allow the anti-sway bar to sit level. If they do not you will need to drill new holes. I've attached an installation video where Shane will walk you through installing the # RM-1139-147.
  view full answer...


• Does The TireMinder i10 TPMS Monitor Have An Internal Battery Or Does It Need To Be Plugged In
• The monitor for the TireMinder i10 TPMS # TM29FR does need to be plugged in. It comes with a power cord that you can either plug into to a USB outlet or you can use the included adapter to plug into a 12v cigarette outlet.
  view full answer...


• Does Roadmaster Exact Center Stabilizer for 2018 Thor Four Winds 24F Use More than 150 Ft lb Torque
• The install of the Roadmaster Exact Center Steering Stabilizer part # RM47MR does not require more than 150 ft lbs of torque. It's not a great idea to use a torque wrench as a breaker bar to loosen hardware. And I'm saying that as someone who has borrowed their current employer's expensive torque wrench and done so in the past. It might be fine but it has potential to screw up the calibration of the wrench.
  view full answer...


• Finding the Correct Replacement Screen For a Roof Vent on a Thor Four Winds 30D
• Unfortunately, your RV information does not indicate what vents/screens that you would have. That being said, 14"x14" vents are significantly more common than 13"x13". The replacement screens that we carry, like the Replacement Screen Frame with Screen # BVC0573-32 which fits the Ventline Ventadome Roof Vent # V2119-603-00 fit inside a 14"x14" roof vent, the screen itself is not 14"x14". The easiest way to identify the correct replacement parts is with model numbers. If you can provide...
  view full answer...


• Parts Required to Install Redarc Tow-Pro Elite Trailer Brake Controller on 2019 Thor Four Winds 31W
• The only part you will need to install the Redarc Tow-Pro Elite Trailer Brake Controller # RED44FR is the brake controller itself. Unfortunately there is no wiring adapter for your vehicle, but that does not mean you can't use this brake controller. Since you have the factory tow package you should have the factory tow port. You will need to splice the wires from the # RED44FR into the wires running to the tow port for installation. I recommend using butt connectors like the # DW05745-10...
  view full answer...